The first thing that you should know when building circuits for electrical devices are the theories in basic electronics. Get to know the various components used in them and how to properly connect them to each other. And study how to make and read schematic diagrams that represents graphically the electrical circuit using images and symbols.
Doing so is important when you like to make a particular device but still confused on some parts of this process. This may be something a bit advance for you like the voltage divider which the output produced is a portion only of its input. Before tackling that, learn first or review the basic theories in electronics to better understand the advance stuffs.
Begin with identifying the types of electricity such as AC or alternating current and DC or direct current. The direction which electrical signal flows on AC is constantly reversing or alternating with the reversal rate measured in Herts. Meanwhile the flow in DC is one direction to ground from power source and found commonly with batteries.
A closed circuit is when the electric current is allowed to pass through a path from power source to ground which normally indicates a device is functioning. While an open one breaks this path and will prevent the movement just like in turning off a machine. This is done with a switch so you could alternate between them instead of removing the source.
Components creates resistance if current pass through from a positive voltage to a ground and a short circuit happens when these two are connected directly. Avoid this direct connections because they would result in breaking, overheating, explosion or fire. Putting only a switch between them is not enough and other parts are needed for additional resistance.
Wiring things together could be done with two ways that are called series as well as parallel and the former indicating that every component is wired after each one. While the latter would indicate that the parts were wired next to the other which makes electricity simultaneously pass them. Both ways can be used together when you build circuits.
Resistors are used in adding resistance to circuits and reduce the current flow with them being available in different values measured in ohms. They also have wattage ratings and their value are indicated by the colored bands on their body. You may learn how to read these bands or just look up graphs that help you calculate their values.
Components which stores electricity and discharges them when they drop are called capacitors and is measured with Farads commonly shown in units of nanofarad, picofarad and microfarad. The types of capacitors commonly used are electrolytic and ceramic disc. The latter being non polarized while the former is polarized requiring one leg to connect properly with either the ground or power.
Diodes are components which are polarized allowing passage for currents in one direction and will cause voltage drop. One side of it is called cathode that connects to power while the other one is anode. These are just a few samples of some basic theories you shall learn for making electrical devices.
Doing so is important when you like to make a particular device but still confused on some parts of this process. This may be something a bit advance for you like the voltage divider which the output produced is a portion only of its input. Before tackling that, learn first or review the basic theories in electronics to better understand the advance stuffs.
Begin with identifying the types of electricity such as AC or alternating current and DC or direct current. The direction which electrical signal flows on AC is constantly reversing or alternating with the reversal rate measured in Herts. Meanwhile the flow in DC is one direction to ground from power source and found commonly with batteries.
A closed circuit is when the electric current is allowed to pass through a path from power source to ground which normally indicates a device is functioning. While an open one breaks this path and will prevent the movement just like in turning off a machine. This is done with a switch so you could alternate between them instead of removing the source.
Components creates resistance if current pass through from a positive voltage to a ground and a short circuit happens when these two are connected directly. Avoid this direct connections because they would result in breaking, overheating, explosion or fire. Putting only a switch between them is not enough and other parts are needed for additional resistance.
Wiring things together could be done with two ways that are called series as well as parallel and the former indicating that every component is wired after each one. While the latter would indicate that the parts were wired next to the other which makes electricity simultaneously pass them. Both ways can be used together when you build circuits.
Resistors are used in adding resistance to circuits and reduce the current flow with them being available in different values measured in ohms. They also have wattage ratings and their value are indicated by the colored bands on their body. You may learn how to read these bands or just look up graphs that help you calculate their values.
Components which stores electricity and discharges them when they drop are called capacitors and is measured with Farads commonly shown in units of nanofarad, picofarad and microfarad. The types of capacitors commonly used are electrolytic and ceramic disc. The latter being non polarized while the former is polarized requiring one leg to connect properly with either the ground or power.
Diodes are components which are polarized allowing passage for currents in one direction and will cause voltage drop. One side of it is called cathode that connects to power while the other one is anode. These are just a few samples of some basic theories you shall learn for making electrical devices.
About the Author:
You can get great tips for picking a voltage divider supplier and more information about a reliable supplier at http://www.rossengineeringcorp.com/products/measurement/hv-voltage-dividers/hv-voltage-dividers-detailed-info.html now.
Tidak ada komentar:
Posting Komentar